A-01Methods
Waterproofing Methods Compared
There is no single best waterproofing. The right method depends on the surface, how much it moves, exposure to sun and standing water, and how the area will be used. Compare the common systems, see which fit each area and estimate the material for your own job.
C-01Compare
Method comparison sheet
General characteristics of each family of systems. Individual products differ, so check the data sheet of the product you are offered.
| Item | ALiquid urethane | BBituminous sheet | CSingle-ply (PVC, TPO, EPDM) | DCementitious | EAcrylic coating |
|---|---|---|---|---|---|
| Applied as | Brushed, rolled or sprayed in coats | Rolls torched on or self-adhered, lapped | Large sheets, welded or bonded seams | Slurry brushed or troweled | Rolled or sprayed in coats |
| Seams | Seamless | Lapped | Welded or taped | Seamless | Seamless |
| Movement | Good elasticity | Good with reinforcement | Good | Low; flexible grades exist | Moderate |
| Sun exposure | Needs a UV-stable top coat | Mineral or coated cap sheet | Most grades made for exposure | Usually covered | Made for exposure |
| Standing water | Good once fully cured | Good | Good | Used under tile and in tanks | Check the rating; often poor |
| Typical places | Flat roofs, balconies, terraces | Flat roofs, foundations | Larger flat roofs | Basements, wet rooms, tanks | Roof restoration, walls |
| Main weak point | Thickness depends on the applicator | Laps and upstand details | Seam quality, punctures | Cracks if the structure moves | Ponding water, thin coats |
Read the comparison as a starting point for questions to your contractor, not as a ranking.
A-01By area
Which method for which area
Pick the area to see the methods that usually fit and the details that need extra care.
- Usually fits
- Liquid urethane, bituminous sheet or single-ply membranes
- Extra care
- Outlets and drains, upstands at parapets, penetrations and edges
- Check first
- Falls to the outlets and the condition of the old layer
- Related post
- Roof membrane options compared
- Usually fits
- Crack repair plus breathable water-repellent or elastomeric coatings; sealant at joints
- Extra care
- Window perimeters, sills and movement joints
- Check first
- Whether the wall must stay vapour-open
- Related post
- Exterior wall membrane, step by step
- Usually fits
- Liquid or sheet membranes made for use under tile
- Extra care
- Drain connection, internal corners, pipe penetrations, floor-wall junction
- Check first
- Falls to the drain and a flood test before tiling
- Related sheet
- Bathroom & shower
- Usually fits
- Exterior membranes where excavation is possible; cementitious or crystalline systems and drainage inside
- Extra care
- Wall-floor joint, tie holes, pipe entries
- Check first
- Whether water is under pressure or just damp
- Related post
- Basement wall from inside, options compared
- Usually fits
- Liquid membranes under tile or as a walkable finish
- Extra care
- Door threshold height, drains, balustrade fixings
- Check first
- Whether water can drain away from the door
- Related post
- Membrane on concrete: five checks
S-02Sequence
How a liquid membrane goes on
The order is the same for most liquid systems; the data sheet sets the numbers.
01/08
Prepare the substrate
Repair cracks and spalls, remove loose coating, dust and grease.
02/08
Check moisture
Measure or test that the surface is within the product's moisture limit.
03/08
Prime
Apply the primer the manufacturer names for that surface.
04/08
Reinforce details
Embed fabric at corners, drains, pipes and cracks.
05/08
First coat
Apply evenly; respect the recoat window.
06/08
Second coat
Build up to the required dry film thickness.
07/08
Top coat
Add UV or wear protection where the area is exposed.
08/08
Cure before use
Keep traffic and water off until the stated cure time has passed.
Q-01Take-off
Coating quantity estimator
Enter your area and the coverage from the product data sheet. The result updates as you type.
Input
Take-off
- Total coated area
- —m²
- Material before waste
- —L
- Waste added
- —L
- Containers
- —pcs
Material to order
—L
Coverage on data sheets is often given per coat at a set thickness. Rough or porous surfaces take more.
General note
Read the data sheet first
Every product lists its own coverage, film thickness, recoat time, cure time, temperature and humidity limits and compatible primers. Those numbers beat any general guide, including this one.
- —Ask the contractor which product and how many coats are in the quote
- —Keep a copy of the data sheet with your building records
- —If two products are combined, check that the manufacturer allows it
Q-02RFI log
Methods FAQ
RFI-01Can urethane go over an old coating?
Response
Only if the old layer is well bonded and compatible, and after the surface is cleaned and primed as the manufacturer says. Loose or blistered layers have to come off first.
RFI-02Is sheet better than liquid?
Response
Neither is better everywhere. Sheets give a known thickness but depend on their laps; liquids are seamless around complex details but depend on careful thickness control.
RFI-03Does cementitious coating stop water under pressure?
Response
Some cementitious and crystalline systems are made for water pressure from the negative side, for example in basements and tanks. Check that the product is rated for it.
RFI-04How thick should a membrane be?
Response
As thick as the data sheet requires for that use. Ask how the contractor will check it, for example by material used per area or wet film gauge readings.
Next sheet
More on membranes
Field notes on roof, wall and concrete membranes.