A-03Bathrooms

Bathroom & Shower Waterproofing

Tile and grout are not waterproof; the membrane underneath is. This sheet shows which zones must be covered, gives you an inspection form to use before tiles go on and helps you decide between resealing, coating and a full re-waterproof.

D-02Details

Wet zones to cover

Six places where bathroom leaks start. Building rules on how far the membrane must extend differ by country; follow yours.

Shower floor and drain

The membrane must lap into the drain's clamping ring or bonded flange. A gap here sends water straight into the floor.

Shower tape mistakes

Shower walls

Covered to at least the height your local rules require, with every board joint banded.

Shower walls post

Tub surround

The wall above the tub and the joint between tub and wall take splash water every day.

Sealing the tub joint

Floor-to-wall junction

Movement between floor and wall cracks rigid layers. Reinforcing band and flexible sealant cover it.

Pipe and valve penetrations

Every pipe through the membrane needs a sealing collar or the manufacturer's detail.

Door threshold

Without an upstand or a set-down floor, water on the floor runs under the door into the next room.

F-02Inspection

Pre-tile inspection form

Use it on site before the tiler starts. Tick only what you have seen yourself, and take photos.

Pre-tile inspection · 7 items

0 / 7 ticked

open

Open items left. Ask for them to be fixed and photographed before any tile goes on; after tiling they are hard to check.

S-04Sequence

Membrane on shower walls

Liquid systems follow roughly this order; sheet systems replace the coats with bonded sheets and taped seams.

  1. 01/06

    Clean and prime

    Dust-free boards or render, primer as the data sheet says.

  2. 02/06

    Band corners and joints

    Embed tape or fabric in the first coat at corners and board joints.

  3. 03/06

    Collar the pipes

    Fit sealing collars around valve bodies and pipes.

  4. 04/06

    Two full coats

    Second coat at right angles to the first, to the required thickness.

  5. 05/06

    Extend beyond the shower

    Carry the membrane past the wet area as specified.

  6. 06/06

    Cure and flood test

    Let it cure fully, then flood test the floor before tiling.

A-03Options

Repair or re-tile?

Pick the option you are weighing to see what it can and cannot do.

When it fits
Leak traced to failed silicone or open grout joints; tiles are firm
What it cannot fix
A failed membrane or broken drain connection under the tile
Ask the contractor
How old sealant is removed and how long before use
When it fits
Porous grout or hairline gaps on otherwise sound tiling
What it cannot fix
Water already trapped behind tiles, loose tiles, drain problems
Ask the contractor
Product name, number of coats, slip resistance on floors
When it fits
Loose or hollow tiles, repeat leaks, damage in the room below
What it involves
Removing tile and bed, drying, new membrane, flood test, new tile
Ask the contractor
Membrane product, drain detail, flood test and written warranty

General note

Paint-on products over tile

Clear or coloured coatings over tile can help where grout is porous, but they do not replace a failed membrane under the tile. If water is already behind the tiles, or tiles sound hollow, the fix starts underneath.

  • —Test a hidden spot first for adhesion and slip
  • —Keep shower drains and joints free of coating build-up

Q-04RFI log

Bathroom FAQ

RFI-01How long should a flood test run?

Response

Membrane makers and local rules set the period; 24 hours is common. Mark the water level, check it at the end and look at the ceiling below.

RFI-02Can a shower be waterproofed without removing tile?

Response

Only surface problems such as joints and porous grout can be treated from the top. A failed membrane under the tile needs the tile removed. See paint over bathroom tile.

RFI-03Is waterproofing tape enough?

Response

Tape is for joints, corners and seams within a full system; it does not waterproof a wall on its own. Common errors are listed in waterproofing tape mistakes.

RFI-04How often should silicone be redone?

Response

When it splits, loses grip, or mould has grown under it. Check it once or twice a year; the sealing sheet has a quick check.

Next sheet

Shower posts

Hands-on notes on shower walls, tape and bathroom paint.